YOUR PLUMBING CRASH COURSE: WHAT YOU MUST HAVE FOR INSTALLING A BATHTUB

Your Plumbing Crash Course: What You Must Have for Installing a Bathtub

Your Plumbing Crash Course: What You Must Have for Installing a Bathtub

Blog Article

Click On This Link

The writer is making a number of great points regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this great article which follows.


Tools You Need to Install a New Bathtub
Installing a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a new one is also a reasonably difficult task. If the old tub is easily easily accessible, the project can relocate immediately; if you have to open up a wall to remove the old tub and place the new tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will need an assistant to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the job as well as fit trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration utilizing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This post will help you mount a brand-new tub in your restroom if you have already gotten a new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices as well as material checklist ought to comprise the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is frequently the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a towel all set for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
    Prior to going on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet and the sink. Protect the tap in place with the producer supplied backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type ought to be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Installing the Tub


    Using both wooden boards under its feet, put the bathtub in the required setting. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 little points.
    The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bathtub until the level reviews degree.
    To mount faucets, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
    Activate the supply of water and examine all joints and brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow outlet and also the regular outlet for leaks.
    Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub ought to wait up until the bath tub has actually been utilized at least once as this will certainly resolve it into its last position.

    Planning for the Installation


    To start with, the supporting framework provided with the bathroom ought to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the tub.
    Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you make use of all of the provided washers.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final setting.

    Tiling Around the Tub


    In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a stiff seal, causing the water to pass through the wall surface between the bathroom and also the tiling, resulting in difficulties with wetness and feasible leakages to the ceiling listed below.
    You can select from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly load the tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not consider this motion prior to sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We were shown that editorial about Tools You Need to Install a New Bathtub from an acquaintance on a different site. Sharing is nice. Helping others is fun. Thank you for going through it.


    Need help? Dial now.

    Report this page